Articles, Blog

Scritte olografiche, come si attaccano?


hello guys here we are all
Monday in my hut today finally let’s see how to assemble this pen that
I do not know if you can see in the room yes, a little you see, on which I have
I attached the words I have attached the holographic writings I have
presented in the last video, if not you saw it, I leave you the card here
so you can go and see it it’s a different way of decorating them
our creations also have an effect pretty nice I still have to improve
a little technical because I have a mountain of waste in the sense that before attacking either
written or throw away at least 6 let’s see how I did it
see you later for the greetings. Let’s take now, our writing from the
water and pebble trying not to fold,
let’s stick it on the pen, calmly, otherwise it breaks, like this and now let’s go out
all the air between the writing and the pen in so that it attacks correctly let’s help maybe even with a stint or
something rigid I’m not very good yet but slowly … Assemble our pen the clip, we pull out all the
components because otherwise there we forget on the street The clip that must be inserted
inside this piece here insert and with the press .. it goes much better than with the drill press well, this piece is inserted then we insert this part of the mechanism on which we screw we screw it up later let’s insert the tip first
after insert the ink the spring Well I hope this video is too
liked it if you liked it naturally a nice thumb up is always welcome,
comment below, share above all share, because this helps us
channels to grow to be known, under always find the links
of last week to find everything the material needed to do these
what’s this what to say, that’s enough, as always, it’s enough me
I recommend sharing, I have already said .. Boh better two than one … Put a big thumb up all that you want see you on Monday
with a new project and just like as always,
that’s enough I hope this time to have looked in the room otherwise someone we know, gets angry … Hello

17 Comments

  1. Angiolina Tadiotto Author

    bella prova….hai le mani troppo grosse….devi farlo fare alla donna, se ha le mani piccole…anche io ho le manone, quindi farei un casino! bravo

    Reply
  2. Nicola Fiorese Author

    Ciao Pedro, complimenti!! Sri sempre il Top con queste lavorazioni. ho l'hobby del modellismo, faccio auto da rally scala 1:43 e la posa decal è una parte fondamentale del processo. Non so se il supporto che usi X le tue scritte sia simile a quello dei miei kit ma potrebbero tornarti utili dei prodotti specifici da modellismo come l'ammorbidente X le decal, che dopo il passaggio in acqua, le rende morbide e più posabili, le picchietti con un cottonfioc e riesci a far uscire gli eccessi di aria e acqua e contemporaneamente ad assorbirla. Ti faccio poi una domanda sulla tua tecnica…perché il cianoacrilato e non una vernice trasparente 2k monocomponente? O della resina epox/poliestere? 😉😉

    Reply
  3. Franco Altobelli Author

    BRAVISSIMO PEDRO CHE LUCIDO USI QUELLO NEL VIDEO E UN COMUNE ATTAK O ALTRO SE LO POSSO SAPERE IN QUESTI GIORNI FARO ANCHE IO IL PRESSA PENNE SPERO COME HO VISTO COME TU LAI FATTO MI DEVE ARRIVARE LO STRETTOIO GRAZIE ANCORA

    Reply
  4. Marco Ingrami Author

    Ciao Pedro, grande lavoro 🙂. Per stendere l'ologramma mi permetto di scriverti che potrebbe aiutarti un semplice cotton fiok. Morbido e assorbente insieme.
    Grazie per il tuo lavoro a favore della community.

    Reply

Leave a Comment

Your email address will not be published. Required fields are marked *